石鑫华视觉 手机微信QQ:13450001061 / 18038383457

下载中心

NI GPIB-Serial Converter Software 1.0 Win32Eng NI GPIB到串口转换软件1.0下载

文章来源:石鑫华视觉网时间:2022-05-18 16:36:45 点击:279

Windows系统下(Linux和MAC系统下请自行了解清楚)NI的各种软件、模块、工具包、驱动程序,使用NI许可证管理器来激活的,绝大部分的都可以使用NI Lincense Activator来激活,以下链接可下载:
NI序列号Serial Number生成激活工具NI License Activator,LabVIEW/VBAI/VDM/VAS等软件模块工具包破解工具不限版本
http://pcmv.cn/thread-490-1-1.html

视觉论坛的各种资源,除了视觉相关的模块有使用外,大部分的都不会使用,所以仅提供资源不能提供技术支持。资源的下载地址一般会同时提供NI官方地址和百度网盘的下载地址。某些工具包NI的地址失效或没有NI的下载地址,那视觉论坛也没有办法,只能尝试使用百度网盘地址下载;如果百度网盘的下载地址失效过期,可联系论坛客服更新。现在NI的下载服务器对我国IP地址不是很友好,有些时候速度很慢或大的资源下载很容易出错,这样会造成安装过程各种类型报错而无法安装。建议在下载完成后,对下载资源做校验和验证(NI一般会提供MD5或SHA256等),与官方或视觉论坛提供的校验和对比,一致就可以安装,如果不一致,则需要重新下载。视觉论坛早期下载的资源,那时候NI没有这么多限制,基本上都是正常下载的资源;后期下载的资源,都与NI的正确校验和对比过,保证是正确的资源才上传到百度网盘,所以百度网盘的资源基本上是正确的。校验和工具下载地址:
文件Hash计算器FHash,文件校验和验证下载文件正确性验证,MD5值计算、SHA1值计算、SHA256值计算、CRC32值计算
http://pcmv.cn/thread-26524-1-1.html

NI GPIB-Serial Converter Software 1.0 Win32Eng NI GPIB到串口转换软件1.0下载

GPIB-Serial Converter Software
GPIB-Serial Converter软件可帮助您配置GPIB仪器控制设备。
GPIB-Serial Converter软件是一个实用程序软件,用于配置GPIB-RS232或GPIB-RS485/RS422转换盒。该实用程序使GPIB仪器控制设备能够将具有RS485、RS422或RS232串行端口的计算机转换为GPIB总线上的讲话者、监听器或控制器。GPIB-Serial Converter软件还为使用GPIB连接第三方仪器提供了最大的可靠性。

1.0Win32Eng
文件大小: 66933024 字节 (63.83 MB)
修改日期: 2010-04-25 03:27
MD5: 4e3398ca7623b29b84f397e2b076a412(官方正确)
SHA1: 369b6fd5a5300e8ff62177298c214d980e1b6678
SHA256: 33d2194578b7a9742cb7eb826a9cd09fd64b5e74d7b5f297afe5237d4e25938b
CRC32: fb82ea8c

百度网盘与NI官方下载地址:

NI GPIB-Serial Converter Software 1.0 Win32Eng NI GPIB到串口转换软件1.0下载

http://pcmv.cn/thread-25988-1-1.html?fromuid=9

(出处: 视觉论坛VISIONBBS|视觉之家VISIONHOME)



NI GPIB-Serial Converter, Version 1.0© 2006 National Instruments Corporation. All rights reserved.


Thank you for using the NI GPIB-Serial Converter, Version 1.0.

This file contains release notes, patent information, and last-minute information for the NI GPIB-Serial Converter software. Some information in this file may be too recent to be included in the official documentation set.

This readme contains the following main sections:

  • Release Notes

  • Features in Version 1.0

  • Contacting National Instruments

  • Patent Information



Release Notes

The NI GPIB-Serial Converter software supports the National Instruments GPIB-RS232 and GPIB-RS485/RS422 hardware interfaces. These products are drop-in replacements for the older GPIB-232/485CT-A and GPIB-232CV-A products. There are no dip switches on the GPIB-RS232/485/422 hardware interfaces. The NI GPIB-Serial Converter software allows you to configure the settings for the hardware, as well as update the firmware, if a new firmware image becomes available.

Supported Interfaces

The following hardware interfaces are supported:
  • GPIB-RS232

  • GPIB-RS485/RS422

The NI GPIB-Serial Converter software must be installed and run on the following operating systems:
  • Windows 2000 Service Pack 4

  • Windows XP Service Pack 2


The configured hardware interfaces have been tested with, but are not restricted to, the following:
  • Windows 2000 Service Pack 4

  • Windows XP Service Pack 2

  • 32-bit x86 processors



Features in Version 1.0Modes of Operation

The GPIB-RS232/485/422 combines the modes of operation from the GPIB-232/485CT-A (G Mode and S Mode) and GPIB-232CV-A (C Mode and D Mode). Refer to the NI GPIB-Serial Converter Help for additional information regarding each mode.

Firmware and Configuration Updates

Use the NI GPIB-Serial Converter Wizard to select the desired mode of operation and configure the GPIB-RS232/485/422 settings. Download firmware images from the web and use the same utility to update the hardware interfaces with the new firmware.

Serial Baud Rates

Baud rates up to 115.2 kb/s are supported. Use the NI GPIB-Serial Converter Wizard to configure this setting.

Secondary GPIB Addressing

Secondary GPIB addressing is available in any mode of operation. Use the NI GPIB-Serial Converter Wizard to configure this setting.

EOI Assertion in C Mode

In C Mode, there is an option to assert EOI with <CR> and <LF> termination modes. The EOI (End or Identity) asserts on the GPIB bus on the terminating byte prior to readdressing the device as a Talker. Use the NI GPIB-Serial Converter Wizard to configure this setting.

Differences between GPIB-RS232/485/422 and GPIB-232/485CT/CV-A

Refer to the NI GPIB-Serial Converter Help for a detailed list of differences between the GPIB-RS232/485/422 and the GPIB-232/485CT/CV-A hardware interfaces.

Contacting National Instruments

Thank you for your interest in the NI GPIB-Serial Converter. We appreciate communicating with the people who use our products. We are also very interested in hearing about the applications you develop using our products. Our Web site, ni.com, provides advanced support and services and contact information.

Patent Information

For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.


首页
84162741QQ
联系